| 13.10.23
|
Elongated ovoid body, tapering at the bottom to a convex but nearly flat base and at the top, more gradually, to a very short neck with concave sides, then a broad rim, slightly concave on upper and lower sides, with a narrow mouth; two lugs (with wavy ridges), parallel to eachother, on either side of the vase, approximately 1/3 below the rim.
|
|
| 13.10.26
|
Shallow bowl; horizontal rim with two holes for suspension at one side, one of the holes has a thin piece of rope in it (modern?)and clay; the base is slightly bulbous (the shape is slightly irregular leading to an incline of the rim to one side); interior smooth; 'ridges' can be felt on the exterior where the clay was turned on the potter's wheel; short, wide resting surface.
|
|
| 2006.12.27
|
Cylindrical. Tapers outward at both ends, with two wider ridges at once end
|
|
| 45.10.1
|
High, curved, thick, black handle which bends back on itself to attach to mouth and at the back to the lower part of the shoulder. At the mouth attachment are two moulded heads; spout has central channel and two ridges at moulded rim. The cylindrical neck becomes bell shaped in its lower part, and a ridge marks its attachment to the shoulder, which is slightly concave. Beyond the handle attachment is a flat rim, offset from the shoulder and, more sharply, from the body beneath it, which is upright but slightly convex. The very short ring foot, with broad resting surface, is as broad as the rim around the shoulder.
|
|
| 50.3.2
|
Tall and slightly lopsided. Steep angled wall with a slightly everted rim and a ridge just below; two ridges at bottom of wall, including join with slightly sloping floor; another ridge marks the join with the cylindrical stem, slightly broadening at the bottom; two ridges mark the join with the trumpet-shaped base. Offset on interior at join of wall and floor. Base conical on underside.
|
|
| 50.4.4
|
Female mask (hollowed at back), with gaping mouth, hollowed eyes, hair arranged in thick ridges, at side of head and above brow (fringe).
|
|
| 58.2.3B
|
Lid: flat rim, domed interior, surmounted by cylindrical knob with two ridges and concave upper surface. Belongs to pyxis, 58.2.3A
|
|
| 68.12.2
|
Short cylindrical knob, flat-topped and double-recessed in centre. The short concave stem connects the cylinder to the short domed lid, in a continuous curve. Beyond a gouge the outer 1.8 cm of the lid becomes slightly concave and after two ridges terminates in a slightly rounded edge.The underside is hollowed just below the knob, and has a short flange intended to sits inside the rim of the pyxis to which it would have belonged.
|
|
| E.63.22
|
Tri-ridged arrow with concave areas between ridges. Attached to a cylindrical shaft.
|
|
| E.65.6
|
Long, thin ornament from a coffin lid: the centre appears to have a kind of knot carved into it with three ridges on either side of this.
|
|
| L.2011.1.58
|
Smooth outside, ridges on the inside.
|
|
| L.2011.1.59
|
Marked ridge at the junction of the narrower part with the wider one; ridges all over.
|
|
| L.2011.1.60
|
Ridges all over.
|
|
| L.2011.1.61
|
Ridges all over.
|
|
| L.2011.1.62
|
Ridges all over.
|
|
| REDMG:1951.131.1
|
Slim alabastron with narrow mouth, projecting rim, slightly convex on the upper surface, and beveled at the edge, flat on the underside; tall, slightly concave neck, offset from a tall ovoid body, with two small lug handles on the upper 1/4 of the body; molded pedestal foot is comprised of a tapering upper element broadening into a disk foot, with a diagonal outer surface, with three ridges, a flat resting surface, and a conical indentation on the underside.
|
|
| REDMG:1951.140.1
|
Broad rim, slightly convex on upper surface, ridged at the outside edge, with overhanging lip; neck, concave in profile, broadens to a nearly flat shoulder that curves sharply to an ovoid body, which narrows sharply at the bottom, where it is joined to a moulded pedestal foot with a splayed base and concave underside; upper part of foot has tapering straight sides; the profile of the base is decorated with two ridges. Two incurving horizontal handles, round in sectiona, are attached to the upper third of the body; a vertical handle, also round in section, emerges from the top of the neck and curves down to the lower part of the shoulder.
|
|
| REDMG:1951.145
|
Cylindrical lid with inset flat top and raised edge, stepping down in three ridges, broader than the width of the walls; slightly tapering walls terminating in offset flanged rim.
|
|
| REDMG:1953.25.32
|
Kalathos-shaped body, with a flaring rounded rim, to the top of which are attached the looped ends of a pair of strap handles, concave on their exterior surfaces; the tubular ends of the loops rejoin the middle of each handle, and below the bottom of each handle, attached at the bottom of the cup, is a spur. Below a carination, the bottom of the cup narrows to a nearly cylindrical stem, ridged at the center, below which it widens, and smoothly curves into the top of a moulded foot, with three ridges, of increasing diameter, on the exterior surface. Within the narrow resting surface is a concave underside, with a conical hollow at centre.
|
|
| REDMG:1961.199.1
|
Very narrow neck, from which loops up a small, narrow strap handle, which rejoins at the middle of the broad shoulder. The shoulder curves into a bulbous body, grooved just above a slightly raised base. The underside is slightly concave at its centre. Some circular ridges (comb ot wire marks) remain on the underside.
|
|