| 13.10.17
|
Barrel-shaped jug, deep-spreading lip, half has broken away. One handle, with a raised area along the middle. Clay on body rounded into a point in the middle of either side.
|
|
| 14.9.50
|
Fragment. Flat-topped projecting rim, flaring outwards. Clay is thick at the point where the rim begins to flare outwards.
|
|
| 2007.9.4
|
Both long edges are curved, one more greatly so, resulting in the width of fragment being much wider at one end, meetimg the horizontal edge at a small point.
|
|
| 2007.9.6
|
Vaguely pentagon shaped, with a very pronounced point on one side.
|
|
| 2007.9.7
|
Four-sided, almost rectangular except for one side which slopes down more genlty, resulting in a noticeably acute point at one corner.
|
|
| 2007.9.8
|
Four-sided, rim edge slightly curved, one side edge curves concavely, creating a long point.
|
|
| 2008.7.35
|
Irregularly shaped rim fragment; fragment is narrowest up near the rim, then broadens down towards the shoulder, and has broken off near the transition from shoulder to body. Possible point where handle was attached
|
|
| 22.3.20
|
Moulded overhanging rim in three sections, reaching to the point of attachment of the handle on the front of the fragment.
|
|
| 25.8.5
|
The handle is in three tiers, with a point at the tip.
|
|
| 26.7.13
|
Rhomboid in section at the base, and curving towards the point; three protrusions at the base would have been used to secure the arrowhead to the shaft.
|
|
| 45.6.68
|
Small circular body with convex shoulder and reservoir meeting at the widest point to form an angular girth. Large filling hole in the center of the body, encircled by a small depression of the discus. Nozzle is flat with slightly curved sides. The tip of the nozzle is flat with rounded, but unequal sides with an oval wick hole. Small shallow circular foot in the center of the body.
|
|
| 48.12.13
|
Short straight tapering neck; shoulder meets the body at a corner point; two small handles are attached to the upper body; the body is bulbous and has no foot.
|
|
| 60.8.3A-B
|
Lid: three tiered round knob with central, nearly conical well; short concave stem curving above and below into knob and lid; nearly flat lid tapering gently to a short vertical rim, rounded at both edges. The underside is slightly hollowed under the knob. Lekanis: shallow bowl with a short nearly vertical flange, rounded at the lip, straight but tapering walls, slightly carinated and narrowing, with convex lower portion, to a very short stem, on a rounded disk foot, with a flat resting surface, curved on the underside, with a rounded point at the centre. A wishbone handle rises from the top of the wall, on either side; a lug protrudes from either side of each handle.
Ure 1960, 216 notes that what remains of the one handle indicates that it was pointed (wish-bone shaped) at the centre as well as rounded in section.
|
|
| 70.3.3
|
Ian McPhee describes it as a Kotyle rather than Skyphos type c (?). Tapering ring base, rounded at the bottom, from which the body rises in a sharp diagonal, curving sharply approximately at the halfway point, from which it rises near vertically and eventually flares slightly to a plain, rounded rim, just below which are attached two horse-shoe shaped handles, almost round in cross section.
|
|
| 71.12.6
|
Wide strigil curved in a tight arc. Handle is square and thinner on the back than the front as it bends over to make an oblong shape. The handle adjoins the strigil in a long triangular point with an incised line acting as a border.
|
|
| 79.1.5
|
Circular body with convex shoulder and a concave discus with small filling hole. Small raised protruding foot with flat base. Large vertical handle with one incised line along the length of it and a second band laying across the handle at the highest point, also with an incision along it. Long spout with irregular splayed tip, large oval wick hole. joining lines of the handle and the nozzle are apparent.
|
|
| 83.2.2
|
Wide at the bottom and short. At the top left long peice of terracotta extends outwards to a narrower point. To the right is the same apart from it has been broken. On top another peice of terracotta extends but again is broken.
|
|
| E.23.23
|
Pear shaped jar with a pronounced lip, short neck, and pointed base, widest point has a ridge which is uneven.
|
|
| E.23.26
|
Everted lip attached to long straight neck, shallow but wide upper body. Lower body gently tapers to an everted foot with a concave base. Handle attaches to just below the top of the neck and rejoins the body at the widest point of the body.
|
|
| E.23.33
|
Lip is unpronounced, long neck flares to shoulder/widest point, which then tapers to pointed foot. The rough handles are directly opposite each other on the widest point.
|
|
| E.62.30
|
Small vase, with pronounced lip and neck. Shoulders are widest point tapering to a flat base.
|
|
| E.62.46
|
Flat and thin blade with a nail through to both sides, perhaps for attaching a wooden handle. The blade is pointed at one end then widens in a triangle then thins again but not to a point.
|
|
| E.62.5
|
Smooth pin, round and tapering to a point.
|
|
| E.63.27
|
A small lip tapering to a narrow mouth. The neck is long leading straight down to globular body the widest point of which is the shoulder. The body tapers to a flat base.
|
|
| E.63.28
|
The lip is narrow, no neck and a weak shoulder. The body flares to the widest point in the lower half of the jar just above the foot. The widest point tapers to the foot, which is approximately 1cm in height with a flat base.
|
|
| L.2016.3.23
|
Almost pyramidal, very coarsely worked artifact, not symmetrical. The 'underside' slightly tapers to a point.
|
|
| REDMG:1951.132.1
|
Guttus type askos: swelling rounded body with bearing at the top a large relief medallion (frontal female mask with puffed cheeks and a lock of hair knotted over the forehead) offset and raised from the body; at a distance of ca. 0.5 cm are two incised lines beyond which the body is covered with fine vertical fluting down to its midpoint. A long diagonal spout with slightly concave sides rises obliquely from the shoulder below the medallion, and terminates in a three-stepped flanged mouth. A loop handle (semicircular in cross section) rises from the shoulder at a right angle to the spout. A tall thick foot, offset from the body, with a ridge at the halfway point broadens toward a ring base, slightly rounded on the exterior, with a concave underside offset from a concave element within the narrow resting surface.
The foot is particularly tall, and is ridged in the middle: otherwise in shape this askos corresponds to Morel's type 8141h 1 (Morel 1981, pl. 209).
|
|
| REDMG:1964.1610.1
|
Ovoid body, convex shoulder, medium rounded filling hole in the centre at the highest point. Nozzle is part of the body and is the most acute angle, elongated oval wick hole piercing the body. Irregular flat lateral pinched handle, base is a slightly raised ring mirroring the ovoid shape of the body.
|
|