| 13.10.26
|
Shallow bowl; horizontal rim with two holes for suspension at one side, one of the holes has a thin piece of rope in it (modern?)and clay; the base is slightly bulbous (the shape is slightly irregular leading to an incline of the rim to one side); interior smooth; 'ridges' can be felt on the exterior where the clay was turned on the potter's wheel; short, wide resting surface.
|
|
| 14.9.52
|
Two fragments forming an irregular shaped piece from handle zone of three-handled jar, with the stump of broken handle.
|
|
| 14.9.59
|
Irregular curved shape with small flat part at right angles (bottom of vessel?)
|
|
| 2004.8.7
|
Solid, irregular trapezoid (six faces). A cylindrical hole piercing the top of the loom (diameter 0.6).
|
|
| 26.7.8
|
Bulbous body, wider in the lower part. Projected rim with a very small discus area leading to an irregular filling hole. Long nozzle with a wide, flat, oval wick hole. Applied strip handle attached to the rim and reaching down to the base. Flat unmarked base. Tall indentation on the left side of the body.
|
|
| 45.6.66
|
Circular deep body with small lip leading to a large filling hole. At the centre of the reservoir is a central circular hollow which is no taller then the rim of the lamp and widens towards the base of the lamp. The nozzle is flat but at a slight incline, the tip of the nozzle is irregular, one side is rounded, the other is angular, the wick hole is oval. Base is a slightly concave ring with parallel circumferences.
|
|
| 45.6.71
|
Circular body with a flat bad around the widest part. Slightly convex shoulder and a concave discus with a small irregular filling hole roughly in the centre. Short nozzle with a rounded tip and circular smoke hole. Vertical handle extends towards base and has a small hole. Base is demarcated but not raised.
|
|
| 78.12.10
|
Circular body, flat moulded shoulder, small concave discus with a small filling in the front right hand side of the discus. Short flat nozzle, rounded tip with a slightly irregular wick hole that cuts into the shoulder area. Vertical handle which reaches down towards the base and attaches around the shoulder, circular piercing through handle. Circular unmarked base, slightly concave.
|
|
| 78.12.11
|
Circular body, flat moulded shoulder, small concave discus with a small off center filling hole. Short flat nozzle, rounded tip with a slightly irregular wick hole that cuts into the shoulder area. Vertical handle which reaches down towards the base and attaches around the shoulder. Circular delineated base, slightly concave.
|
|
| 78.12.16
|
Deep circular body with a rounded shoulder terminating in a large filling hole. Long rounded nozzle titling slightly upwards, irregular rounded tip and an oval wick hole. Large splayed foot. Small vertical lug on the right hand side.
|
|
| 79.1.16
|
Mainly circular body, nozzle is moulded with body disturbing the circular edge back half of body is deeper than the front. Shoulders are convex, discus is concave with a small circular filling hole in the centre. Long deep nozzle, sides follow smoothly on from the body, elongating the circular shape, slightly concave top marked with a ridge on either side, rounded tip and slightly irregular circular wick hole. Remains of small vertical handle attached to the shoulder. Small circular base, slightly concave not lineated.
|
|
| 79.1.5
|
Circular body with convex shoulder and a concave discus with small filling hole. Small raised protruding foot with flat base. Large vertical handle with one incised line along the length of it and a second band laying across the handle at the highest point, also with an incision along it. Long spout with irregular splayed tip, large oval wick hole. joining lines of the handle and the nozzle are apparent.
|
|
| 79.1.8
|
Small circular body with a convex shoulder and a small concave discus with an irregular filling hole at the centre. Nozzle is slightly arched and splayed at the tip with concave edges and an obtuse tip. Wick hole is oval. base is a concave small demarcated circle with a circle within.
|
|
| 79.1.9
|
Deep circular body, small concave shoulder leading to large filling hole. Flat long nozzle with concave sides, a splayed tip and an irregular oval shaped wick hole. Large circular straight sided foot with a concave base.
|
|
| REDMG:1953.25.79
|
Small Circular body, convex shoulder, rim of large central filling hole is concave. Large slightly raised nozzle, rounded tip with a large oval wick hole, slightly irregular underside to nozzle. Small straight sided circular foot with a flat base. Slight anomaly at the bottom of the reservoir in the centre.
|
|
| REDMG:1964.1610.1
|
Ovoid body, convex shoulder, medium rounded filling hole in the centre at the highest point. Nozzle is part of the body and is the most acute angle, elongated oval wick hole piercing the body. Irregular flat lateral pinched handle, base is a slightly raised ring mirroring the ovoid shape of the body.
|
|