| 13.10.1
|
Rat-tanged dirk (sword blade used as a dagger or spearhead), with long thin blade, pointed at both ends, with sloping shoulders. A rib runs nearly the full length of the piece (flattened in the last 2 cm of the blade end). The middle of the rib, near the attachment end, is thin, rhomboidal in section, narrowing to pointed tip or tang which is turned up slightly at the end. Approximately 1/4 down the length of the blade the flange broadens, so that two flat sides spread from the centre rib. The blade end of the dirk has nearly straight sides, but tapers gently to a rounded tip. Catling's type 1d; near Åstrom's type I4. As Catling suggests (1964, 56) the rat-tailed weapon, the most characteristic of prehistoric Cypriote metal forms, occurs in so many sizes that it is impossible to classify them as swords, dirks, daggers, or even spearheads.
|
|
| 2016.3.1
|
Round body, convex shoulders and concave discus with a regular filling hole, roughly at the lower end of the discus; short round nozzle, leading convexly to the base, and round tip with ovoidal wick hole at centre. Vertical round handle, raising up at rear part of the shoulder.
|
|
| 2016.3.2
|
Ovoid body with convex shoulders and wide central filling hole. Body tapers directly into the nozzle with rounded tip, ovoid wick hole at centre and convex sides. Flat ring foot on the base.
|
|
| 2016.5.4
|
Ovoidal body with round base. The shoulders are carved with vestigial tiny lugs handles. Short neck. Half section of the neck is broken off.
|
|
| 23.11.31KK
|
Male facing left, playing pipes. Wearing only a short cloak, which is wound about the shoulders and draped to fall forward over both arms. The left hand holds the pipes to the lips, and the right hand is clenched to grip an incomplete object.
|
|
| 23.11.31NNNN
|
Single fragment consisting of the head and shoulders of a figure facing right. Wearing a large knobbed headdress which is decorated with tall vertical loops with a central line, over long styled hair
|
|
| 51.7.16
|
Wide cup mouth with a reserved, flat rim. Two tripartite strap handles rise up from the neck and join the body at the shoulders. Ovoid body tapers to a thick disk foot, beneath a short (restored) stem. Base is concave
|
|
| 79.1.16
|
Mainly circular body, nozzle is moulded with body disturbing the circular edge back half of body is deeper than the front. Shoulders are convex, discus is concave with a small circular filling hole in the centre. Long deep nozzle, sides follow smoothly on from the body, elongating the circular shape, slightly concave top marked with a ridge on either side, rounded tip and slightly irregular circular wick hole. Remains of small vertical handle attached to the shoulder. Small circular base, slightly concave not lineated.
|
|
| E.62.30
|
Small vase, with pronounced lip and neck. Shoulders are widest point tapering to a flat base.
|
|
| E.62.34
|
Part of jug and basin set (basin missing). Flat base, wide shoulders, tall neck (ca. 6 cm), with striated lip and wide mouth.
|
|
| E.62.39
|
Fine kohl pot with flat base, shoulders and wide, flat rim.
|
|
| E.62.44
|
Lid is oval with a central circular knob and traces of an incised band on top. (Lid is missing!) Body has a flat rim, same shape and size as lid so they sit together, but with a central circular opening. Thin neck leading to shoulders. Four oblong feet at each 'corner' and the base between is flat. Flat rim on top of body is reserved. The inside is a cylindrical well, not matching the contours or shape of the outside. Heavy object.
|
|
| E.63.23
|
Thin lip, narrow neck, curved shoulders and pointed base.
|
|
| L.2011.1.38
|
Front fragment of a lamp, with part of the central discus with filling-hole, part of the shoulders and nozzle. General shape rounded.
|
|
| REDMG:1935.87.21
|
Broad projecting rim with flat lip, narrow cylindrical neck, sloping shoulders curving into an ovoid body, narrowing to a flat base; flat strap handle extends from the rim to the bottom of the shoulder.
|
|
| REDMG:1951.150.1
|
Flaring rim, curving continuously from the exterior, with an overhanging, convex lip, curving on the underside into a short, thick neck that broadens to a baggy body, sharply joined to a broad pedestal foot, flat on the upper surface, convex on the vertical surface, and hollowed slightly interior, with a cyma molding leading up to a flat underside.The triple-ridged strap handles rise up from the sides of the neck and rejoin at the shoulders.
|
|
| REDMG:1953.25.49
|
Round mouth with slightly flaring lip from which rises a vertical strap handle that reattaches at the middle of the shoulder; mouth curves into a short, thin neck, which curves out sharply to sloping shoulders on top of a squat, rounded body; broad, slightly angled foot, with slightly concave base.
|
|
| REDMG:1961.199.3
|
Continuously curving sides: flaring rim, rounded on the upper surface, broad cylindrical neck, nearly diagonal shoulders, ovoid body narrowing to a pinched stem, flaring base, flat (although rough and thus unstable) on the underside.
|
|
| REDMG:1964.1663
|
Rounded, slightly raised rim; two pinched round horizontal handles, round in section, rise at a diagonal from the sloping shoulders which curve gently down to a small raised base, concave on the underside.
|
|
| REDMG:1998.153.4
|
Round mouth with slightly flaring lip from which rises a vertical strap handle that reattaches at the bottom of the shoulder; mouth curves into a short, thin neck, which curves out sharply to sloping shoulders on top of a squat, rounded body; broad, slightly angled foot, with slightly concave base and wire marks.
|
|