Ure Museum Database



Browse
There are 14 objects for which Shape_description contains → parts
13.10.4A-B Two slightly concave disks, not joined (although they sit together well). The lid is thinner than the base with no significant rim, but a beveled edge. The mirror itself has a rim on the underside, and an offset edge on the upper part. These are clearly two parts of a Hellenistic mirror with lid, typical of Hellenistic cyprus. A pair of bronze plates could be locked together because one mirror had a low cylindrical rim into which the other, with a flanged edge, could be fitted. The inside mirror is decorated on the recessed side and polished on the flat side. The outside mirror is polished on the recessed side and sometimes decorated on the flat side. The two polished sides would then lie together, sometimes plated with silver (as in the case of an example in Amathus tomb 62, published in Excavations in Cyprus). For the Greek prototypes see See A. Schwarzmaier, Griechische Klappspiegel: Untersuchungen zu Typologie und Stil (Berlin 1997).
35.5.34 Fragmentary. Foot, handles, and considerable parts of the bowl missing.
45.6.20 Round knob, fragment from lid of lekanis or pyxis, with stem. Knob formed of flat top, with inset circle, depressed centre; profile in two parts, convex on upper part, flat and vertical below; flat underside, offset from short cylindrical stem.
47.10.3A-B Lid: tall, conical, flat-topped knob on a sharply sloping conical lid, with plain rim, vertical profile, flat underside, leading to a short flange (0.3) to sit within lekanis. Lekanis: slightly everted, rounded rim with flat lip, on a deep bowl with straight walls in two parts, separated by a sharp carination near the bottom, attached to a short disk foot, angled on inside and out, with a slightly convex underside. From either side of the rim extends a semicircular horizontal handle, round in section, that rises very slightly, flanked by short pointed spurs or lugs on either side of the handle.
51.4.4 Fragment (two parts, joined together) of the rim, neck and body.
51.7.5 Bell mouth, flaring at the rim, with a convex upper surface, offset from a narrow neck, broadening and curving sharply into the ovoid body; strap handle rises from the top of the neck and joins the lower part of the shoulder; molded ring base, divded into two concave parts, divied by a ridge at the middle; convex underside.
E.62.19 Hammer shaped handle with a slit where the mirror sat in the top. The top parts are curved over. The handle is rounded and wider at the end.
REDMG:1953.25.103 Moulded female figurine with extended arms, wearing headdress. Flat, roughly worked back. Arm position suggests she may have been a singer, forming parts of a ring and is now broken from her base.
REDMG:1964.1669 Rounded everted rim; sides comprised of two concave parts, the upper one larger; flat base.
REDMG:1964.1670 Rounded everted rim; sides comprise two concave parts, the upper one larger; groove inside mouth, approximately 1.0 cm below rim; flat but uneven base with comb or wire marks.
REDMG:1964.1671 Rounded everted rim; sides divided into two concave parts, the upper one larger; flat base with comb or wire marks.
REDMG:1964.1672 Rounded everted and very uneven rim; sides comprise two concave parts, the upper one larger; flat base with comb or wire marks.
T.2012.II.27 Fragment of pot, specifically, the upper part of the handle near the mouth. Two parts of pot handle exist.
TEMP.2003.6.8 Skyphos with ring-shaped foot and one or two handles, missing. a, b, d, and e) Parts of the rim and body. c)Part of the rim and body and the spring of one handle (completely missing). f) The largest part of the foot, base and lowest part of the body. g) Part of the lower body.
The Ure Museum is part of
The University of Reading, Whiteknights, PO Box 217, Reading, RG6 6AH