| 13.10.22
|
Fat Body, narrow neck leading to an out turned rim. One handle joins the shoulder of the vase to the neck directly beneath the rim. Low ring foot.
|
|
| 13.10.26
|
Shallow bowl; horizontal rim with two holes for suspension at one side, one of the holes has a thin piece of rope in it (modern?)and clay; the base is slightly bulbous (the shape is slightly irregular leading to an incline of the rim to one side); interior smooth; 'ridges' can be felt on the exterior where the clay was turned on the potter's wheel; short, wide resting surface.
|
|
| 13.10.8
|
Shallow but wide mortar with small lip and rim. Very thick body gradually leading to a small concave foot.
|
|
| 2016.3.1
|
Round body, convex shoulders and concave discus with a regular filling hole, roughly at the lower end of the discus; short round nozzle, leading convexly to the base, and round tip with ovoidal wick hole at centre. Vertical round handle, raising up at rear part of the shoulder.
|
|
| 26.7.8
|
Bulbous body, wider in the lower part. Projected rim with a very small discus area leading to an irregular filling hole. Long nozzle with a wide, flat, oval wick hole. Applied strip handle attached to the rim and reaching down to the base. Flat unmarked base. Tall indentation on the left side of the body.
|
|
| 45.6.33
|
Outturned rim; tall thin neck leading into broad shoulder with two lugs opposite each other; almost vertically-sided body; flat base surrounded by very slight ridge.
|
|
| 45.6.66
|
Circular deep body with small lip leading to a large filling hole. At the centre of the reservoir is a central circular hollow which is no taller then the rim of the lamp and widens towards the base of the lamp. The nozzle is flat but at a slight incline, the tip of the nozzle is irregular, one side is rounded, the other is angular, the wick hole is oval. Base is a slightly concave ring with parallel circumferences.
|
|
| 45.6.69
|
Restricted lateral ellipsoid body, long convex shoulder shallow lower body. Large filling hole in the center of the body. Beginnings of a flat nozzle with concave side and a circular wick tube. Moderate straight sided foot with concave base, leading to a 'kick' on the internal side of the base.
|
|
| 47.10.3A-B
|
Lid: tall, conical, flat-topped knob on a sharply sloping conical lid, with plain rim, vertical profile, flat underside, leading to a short flange (0.3) to sit within lekanis.
Lekanis: slightly everted, rounded rim with flat lip, on a deep bowl with straight walls in two parts, separated by a sharp carination near the bottom, attached to a short disk foot, angled on inside and out, with a slightly convex underside. From either side of the rim extends a semicircular horizontal handle, round in section, that rises very slightly, flanked by short pointed spurs or lugs on either side of the handle.
|
|
| 58.2.4
|
Wide rim with bevelled lip. Long wide neck leading to a short and rounded body, base protrudes from body but has been damaged (during firing process ?). The handle attaches to the top of the body and then again at the join of the rim and the neck. There is a fork shaped spur which follows the curve of the handle and rim and then continues above the main body of the jug.
|
|
| 61.6.1.4
|
Very uneven in shape. Surface left very rough. The lip is uneven, leading into a very open interior which is widest at the mouth. The body is rough, while the base is also roughly made with no smooth finish to the edges.
|
|
| 78.12.1
|
Deep circular body, almost flat shoulder, leading to a deep concave discus with two small holes, the frontal one is slightly off centre. Very small rounded nozzle with a large circular wick hole. Vertical handle opposite the nozzle, flat base with no delineation.
|
|
| 78.12.18
|
'Cocked hat' lamp, shallow open lamp fashioned from a bowl with two sides folded in to provide a wick rest. The rim is thick and very pronounced leading on to a vertical sided shallow reservoir. the base is flat but there is no foot.
|
|
| 78.12.5
|
Shallow circular body, slight shoulder leading to a large concave discus with a filling hole on the central axis, but further forward. Medium nozzle with concave sides leading to a rounded tip with a circular wick hole. Delineated base, slightly concave. Vertical band around the edge of the whole lamp, probably from joining.
|
|
| 79.1.9
|
Deep circular body, small concave shoulder leading to large filling hole. Flat long nozzle with concave sides, a splayed tip and an irregular oval shaped wick hole. Large circular straight sided foot with a concave base.
|
|
| E.62.44
|
Lid is oval with a central circular knob and traces of an incised band on top. (Lid is missing!) Body has a flat rim, same shape and size as lid so they sit together, but with a central circular opening. Thin neck leading to shoulders. Four oblong feet at each 'corner' and the base between is flat. Flat rim on top of body is reserved. The inside is a cylindrical well, not matching the contours or shape of the outside. Heavy object.
|
|
| E.63.27
|
A small lip tapering to a narrow mouth. The neck is long leading straight down to globular body the widest point of which is the shoulder. The body tapers to a flat base.
|
|
| REDMG:1951.150.1
|
Flaring rim, curving continuously from the exterior, with an overhanging, convex lip, curving on the underside into a short, thick neck that broadens to a baggy body, sharply joined to a broad pedestal foot, flat on the upper surface, convex on the vertical surface, and hollowed slightly interior, with a cyma molding leading up to a flat underside.The triple-ridged strap handles rise up from the sides of the neck and rejoin at the shoulders.
|
|
| REDMG:1953.25.78
|
Circular shallow body, concave shoulder leading to a large filling hole. Beginnings of a band handle. Wide shallow nozzle tilts slightly upwards, large oval wick hole. flat unlimited base.
|
|
| REDMG:1964.1604.1
|
Circular body with small convex shoulder leading to a large circular filling hole. Nozzle is straight sided with a slightly dipped tip, level top and a oval wick hole. Handle was a horizontal band handle around the back. Base is circular, large and has a very slight depression.
|
|
| REDMG:1964.1608.1
|
Small circular body, convex shoulder, concave rim leading to a large circular, central filling hole. Flat long nozzle with slightly down-turned oval wick hole and a rounded tip. Small circular strait sided foot with flat base.
|
|
| REDMG:1964.1613.1
|
Circular shallow body with rounded convex shoulder leading to a concave discus with two small filling/air holes along a central axis. Nozzle is of an average length with a rounded wick hole. large un-pierced pinched vertical handle, small circular, slightly concave demarcated base.
|
|