| 14.9.116
|
Two joining fragments
|
|
| 14.9.78
|
Two joining fragments; Body sherd of Clazomenian black-figured pottery amphora;
|
|
| 14.9.89
|
One of three joining fragments (with 14.9.90-91) preserving part of the rim.
|
|
| 22.3.12
|
Fragment; two joining pieces
|
|
| 26.2.5
|
Rim and body sherd (three joining but not mended fragments) of East Greek (North Ionian) pottery rosette bowl;
|
|
| 26.2.74-75
|
Two joining fragments; Shoulder sherd of Attic black-figured pottery small-neck-amphora;
|
|
| 26.2.82
|
Two joining fragments (physically not joined) of rim of Laconian black-figured pottery kylix;
|
|
| 48.5.2
|
Mouth has thin rim and near vertical walls tapering down to neck; two upside down U-shaped handles start mid-neck and curve upwards before joining the shoulder; inverted ovoid body; near conical foot with mirrored concave base.
|
|
| 50.4.20
|
Outward facing lip on a rim folded into a grape leaf shape, shape continues down neck. Neck joins a plain convex shoulder. Tapering lower body joining slightly taurus foot with slightly concave base. Curved vertical handle attached to the lip and the shoulder
|
|
| 50.4.5
|
Type 7a. Cut-away neck, with a vertical strap handle attached to the lowest part, rejoining the body at the bottom of the shoulder; cylindrical neck sharply joining sloping shoulder, which curves into the ovoid upper body, tapering into a cylindrical lower body; raised base; reserved on the interior, underside and resting surface.
|
|
| 56.8.4
|
Shape 1; trefoil-lip joining at the back to a high curving vertical strap handle, which joins at the shoulder; ring base.
|
|
| 71.12.4
|
Ornamental fibula (pin). Long straight pin with pointed end attached to semi-circular piece that thickens and flattens at the end. There is no hinge here but a curled piece joining the pin and the semi-circle acts as a hinge.
|
|
| 78.12.5
|
Shallow circular body, slight shoulder leading to a large concave discus with a filling hole on the central axis, but further forward. Medium nozzle with concave sides leading to a rounded tip with a circular wick hole. Delineated base, slightly concave. Vertical band around the edge of the whole lamp, probably from joining.
|
|
| 79.1.5
|
Circular body with convex shoulder and a concave discus with small filling hole. Small raised protruding foot with flat base. Large vertical handle with one incised line along the length of it and a second band laying across the handle at the highest point, also with an incision along it. Long spout with irregular splayed tip, large oval wick hole. joining lines of the handle and the nozzle are apparent.
|
|
| REDMG:1953.25.15
|
Trefoil lip attached at the the back to a broad, high curved strap handle that curves in slightly to the middle of the shoulder; short cylindrical neck joining stepped shoulder in a continuous curve; globular body curves into a short ring foot with diagonal resting surface and slightly concave underside.
|
|
| REDMG:1953.25.44
|
Flaring rim, with concave profile, joining bulging body at a carination, below which are attached two u-shaped horizontal handles, rounded in section, canted slightly up; below handles body curves sharply towards stem, broken off.
|
|
| REDMG:1953.25.51
|
Upturned rim, slightly offset from the neck, which is cylindrical and nearly straight, joining an ovoid body, slightly baggy, supported by a broad ring base. Vertical strap handle, grooved, extends horizontally from the rim and curves back into the body, which it joins in the upper part.
|
|
| REDMG:1961.150.1
|
Spreading lip, flat, with rounded rim, above tall, cylindrical neck, with ridge at center, just above attachment of l-shaped strap-handle, joining at centre of shoulder; squat piriform body, nearly flat base, ridge at exterior, groove just within.
|
|
| REDMG:1964.1609.1
|
Ovoid body with handle and nozzle included in the shape. Flat shoulder, raised rim of discus and slightly sunken discus with filling hole just off the central axis to the front right. Small straight sided nozzle, rounded tip with large, slightly oval wick hole. Small pinched vertical handle attaching from the discus down towards the base. Small unmarked circular base, slightly concave. joining marks still distinguishable.
|
|
| REDMG:1964.1616.1
|
Ovoid body with handle and nozzle included in the shape. Flat shoulder, raised rim of discus and slightly sunken discus with filling hole just off the central axis to the front right. Small straight sided nozzle, rounded tip with large, slightly oval wick hole. Small pinched vertical handle attaching from the discus down towards the base. Small unmarked circular base, slightly concave. joining marks still distinguishable.
|
|