Ure Museum Database



Browse
There are 12 objects for which Shape_description contains → flanged
13.10.4A-B Two slightly concave disks, not joined (although they sit together well). The lid is thinner than the base with no significant rim, but a beveled edge. The mirror itself has a rim on the underside, and an offset edge on the upper part. These are clearly two parts of a Hellenistic mirror with lid, typical of Hellenistic cyprus. A pair of bronze plates could be locked together because one mirror had a low cylindrical rim into which the other, with a flanged edge, could be fitted. The inside mirror is decorated on the recessed side and polished on the flat side. The outside mirror is polished on the recessed side and sometimes decorated on the flat side. The two polished sides would then lie together, sometimes plated with silver (as in the case of an example in Amathus tomb 62, published in Excavations in Cyprus). For the Greek prototypes see See A. Schwarzmaier, Griechische Klappspiegel: Untersuchungen zu Typologie und Stil (Berlin 1997).
26.12.31 Mouth flanged and bottom of body angular. Vertical ring handles, spurred. Bottom of vase somewhat angular. Finely moulded foot, side grooved, underside concial with resting surface.
51.7.2 Lid: slightly convex top with circular groove (1.9 cm diam.) at the centre, overhanging a cylindrical body, with straight sides, terminating in a rounded rim at bottom. Pyxis: high cylindrical body with straight sides and simple rounded rim sits atop a flanged element, with rounded edges, that slopes sharply to a foot ring with tapered interior edge and rounded resting surface.
73.10.1 Tall knob, circular in section, flat at top except for a grooved section; knob which narrows then widens to a carination towards the bottom, and narrows again to the join with the concave lid. Flanged rim.
91.11.1 Tall bottle with wide flanged lip; very long and narrow neck; stout conical shaped body with flat resting surface and slightly concave base.
REDMG:1935.87.17 Convex sides; no handles, flanged lid.
REDMG:1951.132.1 Guttus type askos: swelling rounded body with bearing at the top a large relief medallion (frontal female mask with puffed cheeks and a lock of hair knotted over the forehead) offset and raised from the body; at a distance of ca. 0.5 cm are two incised lines beyond which the body is covered with fine vertical fluting down to its midpoint. A long diagonal spout with slightly concave sides rises obliquely from the shoulder below the medallion, and terminates in a three-stepped flanged mouth. A loop handle (semicircular in cross section) rises from the shoulder at a right angle to the spout. A tall thick foot, offset from the body, with a ridge at the halfway point broadens toward a ring base, slightly rounded on the exterior, with a concave underside offset from a concave element within the narrow resting surface. The foot is particularly tall, and is ridged in the middle: otherwise in shape this askos corresponds to Morel's type 8141h 1 (Morel 1981, pl. 209).
REDMG:1951.135.1-2 Pyxis: Flanged rim widening to sharply curved shoulder, rounded below, and tapering to a flat base; round horizontal handles on either side pressed up against rim to form lugs. Lid: cylindrical knob attached to a disk.
REDMG:1951.145 Cylindrical lid with inset flat top and raised edge, stepping down in three ridges, broader than the width of the walls; slightly tapering walls terminating in offset flanged rim.
REDMG:1953.25.38 Lekanis: slightly everted rim with diagonal flange, curves in to a shallow bowl; two flanged ribbon handles, attached horizontally just below rim; pronounced ring foot with vertical sides and raised underside. Lid: Moulded knob with deep circular depression; in centre of sloping lid, which steps down with three fasciae and then a convex lower part decorated with two incised bands; rounded rim.
REDMG:1953.25.39 Flanged rim and tapering body, to which are attached broad horizontal strap handles (rounded but almost oblong in shape), slightly canted upwards, with spurs on either side. The lower body is offset from the handle zone, rounded in the lower part where it attached to thick stem broadening to a moulded foot, with spreading upper part, slightly concave, and a broader, rounded lower part, broadening towards the base, with a conical depression on the interior, and a narrow resting surface
REDMG:1953.25.41 Flanged rim and tapering body, to which are attached horizontal triangular strap handles, slightly canted upwards. The body narrows sharply to short stem, slightly offset from the top of a moulded foot, with a vertical exterior surface and a conical indentation on the underside, and a narrow resting surface.
The Ure Museum is part of
The University of Reading, Whiteknights, PO Box 217, Reading, RG6 6AH